Welcome To DIY Tube Video Community

Get PAID for video views, comments, thumbs up and more. Learn More

Investment Opportunities & Earn A Passive Income: Learn More

Making A Radiant Energy Bedini Charger Using Scrap Parts

Making A Radiant Energy Bedini Charger Using Scrap Parts

Do It Yourself Electronics

1 year
Share
Want to watch this again later?
Sign in to add this video to a playlist. Login
Report 0 7
Category:
Description:
I built a roller skate wheel bedini radiant energy battery charger using all recycled parts.

The roller skate wheel was given to me many years ago in a package along with others. I think it was either just tinted from age or hardened. No matter, it was never used and it is a wheel with bearings.

The electronics come from an old Bedini motor I made long ago using printer and computer parts.

The three coils come from a laser printer and the other parts are most likely from that as well. I dont remember.

This was originally running with a hard drive motor that had magnets glued to it. But mice destroyed that and I kept the electronics all these years. This is a basic Bedini SSG (Simplified School Girl) motor, or radiant energy charger. This is also known as a pulse motor. A side effect of this device is that it desulfates lead acid batteries.

I took some scrap wood and made a base for the Bedini SSG motor. Some scrap pieces of wood made the feet. And another scrap made a side mount for the electronics.

I put a hole in the center for the wheel. I mounted that with a screw.

After locating the North poles of four round ceramic magnets I hot glued them to the roller skate wheel. I had previously cut some flat spaces to hold the magnets.

I put the coils around the wheel and connected the wires to see if I could get it to spin up.

Eventually, after swapping the power coil wires around, I had it running. But nothing was mounted so then I secured the coils in place using zip ties and holes through the base board. Now I can adjust the coils as needed.

A better screw held the wheel in place and it runs happily.

I am using a small 12 volt battery to power the device. Right now it is charging up an old car jump starter and power station.

This device did not like a digital meter so I connected an analog meter to monitor what was going on with the charge battery.

I tried to run this on a 6 volt battery but it ran very slowly and eventually came to a stop. I figure the bearings are too stiff. With time they will loosen up some and I think I can get it to run on a 6 volt battery with no problem.

Comments:

Comment
Up Next Autoplay
Unigear Affordable Hammock Bug Net
Unigear Affordable Hammock Bug Net
Category: Outdoor And Sports
otrbob 5 hours
Video Request Snugpak Underblanket Set Up
Video Request Snugpak Underblanket Set Up
Category: Outdoor And Sports
otrbob 6 hours
Revisit $28 Subito Hammock Underquilt. Winter Camping.
Revisit $28 Subito Hammock Underquilt. Winter Camping.
Category: Outdoor And Sports
otrbob 6 hours
12-11-19
12-11-19
Category: Miscellaneous
mmm9mmm9 7 hours
Quik tip   Underquilt Hack..
Quik tip Underquilt Hack..
Category: Outdoor And Sports
otrbob 9 hours
DIY Bug Net Spreader Bar
DIY Bug Net Spreader Bar
Category: Outdoor And Sports
otrbob 9 hours
Affordable Lhedon Hammock Review
Affordable Lhedon Hammock Review
Category: Outdoor And Sports
otrbob 9 hours
DIY
DIY "Turn Over" Over Cover
Category: Miscellaneous
otrbob 10 hours
Is SONY Movie Studio SUITE 13 Good?
Is SONY Movie Studio SUITE 13 Good?
Category: Miscellaneous
Phillip20 23 hours
HOUSE FIRE BURNING WILDLY OUT OF CONTROL IN FULL HD .
HOUSE FIRE BURNING WILDLY OUT OF CONTROL IN FULL HD .
Category: Miscellaneous
Phillip20 23 hours